Thorens TD-150 Rebuild Part Two, Project Maple

If you haven’t yet read Part One of this series, please do so now. Herein we will cover the build of a relatively stock Thorens TD-150 MK II turntable, though in a custom Maple plinth to Linn dimensions. Should you wish to do this yourself, please do view the rest of the series and this post covering the LP12 Plinth Dimensions.

Maple Td 150 Original Top Cover Off

We start with a TD-150 that looks as though it has already seen a transformation or two. This model previously had a factory-fitted Thorens arm, as it has the arm lift knob and a couple of remnants of that mechanism still in place.

Maple Td 150 Original Close Up Of Top Cover And Platter Off

It’s looking a bit sorry for itself, however. The top trim is no-longer adhered and the plinth is less than ideal. The baseboard is a poor fit and the deck, which would once have held pride of place in a ‘70s audiophile system, looks more like a DIY hack job gone wrong. We can do better than that.

Maple Td 150 Original Close Up Of Sub Platter Top View

I mercilessly tore the deck apart, ditching the plinth and old arm board. The motor, top plate and sub-chassis remained, as did the sub platter and outer platter which were in nice condition. The deck even had the original mat and 45 RPM adapter.

Maple Td 150 Original Front View

I cleaned up the parts with Meguair’s NXT Generation all metal polish. This is wonderful stuff which isn’t too abrasive and can be applied using a microfibre cloth and very little elbow grease. The odd spot of corrosion and any surface marks were sanded to 180-grit and several coats of polish were then applied before the parts were buffed to a shine.

Maple Td 150 Close Up Of Oiled Plinth

Now for a new plinth. The plinth was constructed from 28 mm Maple and built to Linn LP12 dimensions, though the cutout for the top plate was made 0.5 mm deeper to accommodate a stock TD-150 top plate. The plinth is mitred and glued with PVA wood glue and no additional fasteners used in its construction.

Maple Td 150 Clamped Up

I decided not to rebate the triangular braces. They are cut from scraps of the same material and are significantly thicker than those of a Linn plinth. They were glued in place while the plinth was setting and helped to keep things square. Some cuts were made in their outward-facing edges to ensure clearance for the speed mechanism and arm.

Maple Td 150 Close Up Of Switch

The baseboard rebate is 10 mm, as I had intended to use acrylic for the baseboard. I instead went for a plywood shower panel, which is laminated on both sides and is approximately 10.5 mm thick, ideal for our needs.

A 24 mm Forstner bit was used to sink the inserts for the feet, which were then knocked into place. The same Forstner drilled access holes for the 3 suspension adjustment bolts and a hole through which to drop the arm cable.

Maple Td 150 Parts Fitted And Wired

The top plate was secured in place using 3.5 x 20 mm stainless steel wood screws so as not to risk a reaction between metal and wood, though is is usually only a consideration with Oak. Additional holes were drilled to provide a firmer fixing to the plinth and minimise rattling and loose spots. These, and the original holes, were countersunk with the tip of a 12 mm drill bit to sit the screws flush with the plate, allowing the decorative aluminium trim plate to be secured with double-sided adhesive tape as in the original Thorens design.

Maple Td 150 Top View With No Platter

A new plate was cut from 1 mm sheet aluminium using the old plate as a template. With the plate sandwiched between 4 mm plywood, straight cuts were made with a sliding mitre saw and the large circular cutout made with a jigsaw fitted with a metal cutting blade. The only feature this new plate lacks is the lettering for the power / speed dial, but that is a minor inconvenience. Right is 45, left is 33 and the middle position is zero or off.

Aap12 Both Arm Boards Oiled

An arm board was machined in maple at just over 12 mm in thickness. It was bolted to the sub-chassis using 4 30 mm stainless bolts. A 23 mm hole was drilled at a distance of 222 mm from the centre spindle to fit a Rega arm. A stock Rega RB202 was selected and bolted into place with 50 mm M3 bolts, which allow for VTA shims in future should they ever be necessary. The cable drops through a hole in the baseboard directly beneath.

The electronics are identical to the Thorens design, albeit with more modern components. A 0.01uF suppression capacitor sits across the switch and there’s a 0.33uF motor phase capacitor, both class X2 rated for use at mains voltages and both far higher than the maximum of 250V they will see under normal use. The dropping resistor was replaced too with a 5600Ω (5K6) wire wound resistor, and is used to drop the 220-240V mains supply down to the 110-120V for which the motor is designed. A standard terminal block was used, exactly as in the original TD-150. I could (should) have added an internal fuse too, but there’s a fuse in the plug and as this was clearly good enough for the past 5 decades, it’s good enough now.

Maple Td 150 Close Up Of Wiring

Balancing the suspension is a subject I discuss in Part Four. I made a frame to facilitate this, essentially an open-top table in which the turntable plinth can sit. The frame is then levelled to level the edges of the plinth, and the underneath can be accessed to tweak the suspension.

Maple Td 150 Top View Platter On

In terms of things we’ve changed from the stock configuration. The plinth has obviously been replaced, as was the decorative trim plate covering the top plate screws. All bolts were replaced with Allen head equivalents, and the spring bolts extended to 60 mm to accommodate different springs as my originals were too worn to be used. The electronics were replaced but with components of an equivalent electrical specification. The arm is obviously not a stock Thorens arm, but neither of my decks came with one of those. And the arm board is wider.

Maple Td 150 Front View

Aside from this, our top plate, sub-chassis, platter, sub platter, bearing and motor are original – in short, most of the components responsible for the deck’s performance. Even the oil is as original as possible. I used Mobil DTE Medium VG46 turbine oil, which is a close modern replacement for the original oil used by Thorens. This was used to lubricate both the platter bearing and motor.

Maple Td 150 Top View With Record On

And there we have it, a stock TD-150 transformed but with its original charm intact. Look out for Part Three in which we’ll build the AAP12 and see just how far the humble TD-150 can be taken.

By Ashley

I founded Audio Appraisal a few years ago and continue to regularly update it with fresh content. An avid vinyl collector and coffee addict, I can often be found at a workbench tinkering with a faulty electronic device, tweaking a turntable to extract the last bit of detail from those tiny grooves in the plastic stuff, or relaxing in front of the hi-fi with a good album. A musician, occasional producer and sound engineer, other hobbies include software programming, web development, long walks and occasional DIY. Follow @ashleycox2

4 comments

    1. Just 0.5MM2 two-core flex. Standard lighting flex works fine. There’s hardly any current involved, I just used what I had lying around.

  1. Any Idea where I could find parts S 800 816 and 817; belt guide and belt lever/rod” I have A Thorens TD 150 AB MK I. They are missing.

Share Your Thoughts

Discover more from Audio Appraisal

Subscribe now to keep reading and get access to the full archive.

Continue reading